How to Reset Setek WiFi Extender?

Is your signal dropping, or your device is just not able to connect to the internet anymore, or maybe internet is showing up but you arent able to load anything.

Whatever the case is, resetting your Setek WiFi Extender can often clear up the chaos. It's like restoring your device to its default settings.

If you're looking for a guide that is hassle free and gives you easy to follow methods to reset your WiFi extender. Youre in the absolutely right place.

Lets get started!

What Does "Reset" Actually Mean?

We're not talking about turning off the WiFi and turning it back on. Instead, a reset wipes everything. It returns your Setek WiFi extender to factory settings, like how it was the day you first unboxed it.

That means any custom settings, saved networks, passwords will all be gone. And it is absolute clean start.

And sometimes? Thats exactly what you need.

Does Your Setek WiFi Extender Require a Reset?

Before we jump to steps, lets talk about is reset even required for your device?
Reset should be done in the situations given below:

• Youve changed your main router or WiFi password

• You forgot the extender's admin password

• Connection is slow or keeps dropping

• You're setting it up in a new home

• Something just feels off and nothing is working

Whatever brought you here, a reset often solves majority of your problems

How to Reset Your Setek WiFi Extender?

Follow the steps given below, to reset your extender hassle-free:

1. Find the Reset Button

This is usually a small pinhole on the back or bottom of the extender. Youll need something narrow to press the button, such as: a paperclip, or SIM ejector.

Its not always labeled clearly, but look for a little hole labelled as RESET or just a circle outline.

2. Plug In and Power Up

Before pressing anything, make sure your extender is plugged into a power outlet and the lights are turned on.

Dont reset while its booting. Give it about 30 seconds after plugging in so its fully ready.

3. Press and Hold the Reset Button

Now, take that paperclip or pin and press the reset button. Hold it down.

How long? Long press the button for around 15-20 seconds. Watch the lights on the extender, theyll usually blink or turn off when the reset begins to happen.

Now, release the button and give it a minute or two. The extender will reboot itself and go back to its original state.

Youll know its done when the LED lights settle into their usual startup pattern or go blank, depending on your model.

What is to be done, after the RESET?

After the successful reset, youll need to set it up again; just like you did the first time you used it.

Heres how to do it?

1. Connect your phone or laptop to the extenders default WiFi network (usually something like SETEK_EXT)

2. Open a browser and go to: 192.168.10.1 or mywifiap.net.

3. Log in using default credentials (username: admin, password: admin) unless otherwise specified on device label.

4. Connect the extender to your home WiFi network by following the setup procedures.
   If this is your first time, take your time.

5. Make sure you type your main WiFi password correctly. And pick a good spot. The best location is midway between your router and the poor signal.

Common Mistakes to Avoid

All humans make errors. But these ones are a bit common:

• Releasing the reset button too early Hold it for at least 10 seconds. Count slowly if you need to.

• Trying to set up before reset finishes Be patient. Give the device time to reboot.

• Connecting to the wrong WiFi name after reset After reset, the extender will go back to its default network name.

• Placement of the Device: Set up near your router, then transfer it to the final location after it's operating.

Just follow the steps. Sometimes it seems like rocket science, but it's not.

Still Not Working?

If the reset didnt fix your issue, dont worry. Here are a few things that you need to check:

• The extender isnt getting enough power (try another outlet)

• Your router has MAC filtering enabled (check your router settings)

• Firmware might be outdated (visit the Setek website to see if there's an update)

If youve tried it all and still nothing? Might be time to consider an upgrade. Some extenders just dont age well.

Wrap It Up

Theres nothing magical about the reset process. But it works wonderfully, especially when your Setek WiFi Extender stops doing its job properly.

It gives you a chance to start over. To wipe the slate clean and get things working again.

So, the next time your extender gives you grief, dont waste hours guessing. Just reset it, set it up fresh, and get back online.

FAQs

Q1: Will resetting delete all saved networks?
Yep. A reset clears everything. Youll need to reconnect it to your WiFi from scratch.

Q2: My reset didnt work. What now?
Double-check if you held the button long enough. If you did, try plugging it into a different outlet and reset again.

Q3: How do I know its actually reset?
The default WiFi name (like SETEK_EXT) should show up again, and setup instructions will restart when you connect.